[MITgcm-support] [SPAM] Re: FW: Diagnose momentum equation

[Jean-Michel Campin]

Hi Lianzhan,

Two quick things:
1)
> The attachements are "data" and "dada.pkg" files of my exp. 
I did not find these attached files. Are you sure you really included them ?

2)
> What type of forcing do you have in this set-up ?
An answer to this question would be useful.

Cheers,
Jean-Michel

On Mon, Sep 28, 2015 at 05:44:07PM +0800, lianzhan at fio.org.cn wrote:
> Hi Jean-Michel:
> 
> Thank you so much for your help!
> 
> The attachements are "data" and "dada.pkg" files of my exp. 
> 
> About U/Vm_dPHdx, I think you are right. But in this exp, I have used Non-linear free-surface and apply free surface effect to column total thickness (implicSurfPress = 0.5 & nonlinFreeSurf=4 ...). So how could I output the pressure anomaly horizontal gradient caused by the fluctuation on sea surface?
> 
> I am still trying to figure out what happen with U/Vm_Cor and U/Vm_Advec. Does "U/Vm_Advec" respresent the "UdU/dx+VdU/dy+WdU/dz" term in momentum equation? What is the different between "U/Vm_Advec" and "U/Vm_AdvZ3"?
> 
> Thanks again!
> 
> Cheers
> 
> Lianzhan
> 
>  
> From: Jean-Michel Campin
> Date: 2015-09-26 23:19
> To: mitgcm-support
> Subject: [SPAM] Re: [MITgcm-support] FW: Diagnose momentum equation
> Hi Lianzhan,
>  
> It's likely that if Temp & Salt remains uniform, U/Vm_dPHdx will be zero
> (no hydrostatic pressure anomaly horizontal gradient).
> Not very clear why U/Vm_Cori would be zero everywhere except for surface level,
> unless the velocity (uVel,vVel) is also zero everywhere below k=1.
>  
> What type of forcing do you have in this set-up ?
>  
> If you could send (in attachement) the 2 parameter files "data" and
> "data.pkg", this would help to figure out what is happening.
>  
> Cheers,
> Jean-Michel
>  
> On Sat, Sep 26, 2015 at 01:27:27PM +0000, lianzhan wrote:
> > Hello everyone
> > 
> > I want to diagnose the effect of all items in momentum equation (as below for zonal).
> > dU/dt+UdU/dx+VdU/dy+WdU/dz=fv-1/rho*dP/dx+Fx+taux/rho
> > Fx is dissipative stress, taux is wind stress. Is there any corresponding variable in pkg/diagnostics ? I have tried "U/Vm_Advec" for nonlinear term, but this variable is zero expect for the surface layer. Its value is as same as "U/Vm_Cori", the value of "U/Vm_Cori" is also zero below surface. And "U/Vm_dPHdx"(pressure gradient force ? ) is all zero.
> > The settings of my exp is that there is an island located in an ideal rectangular bay,  near which there is a sill. The model has 32 vertical layers and with free surface. The Temp/Salt is uniform. 
> > Do you have any recommendations or suggestions?
> > Thanks in advance for your helpCheers,Lianzhan
> > 
> > 
> > xiaober at outlook.com
> > 
> >             
>  
> > _______________________________________________
> > MITgcm-support mailing list
> > MITgcm-support at mitgcm.org
> > http://mitgcm.org/mailman/listinfo/mitgcm-support
>  
>  
> _______________________________________________
> MITgcm-support mailing list
> MITgcm-support at mitgcm.org
> http://mitgcm.org/mailman/listinfo/mitgcm-support

> _______________________________________________
> MITgcm-support mailing list
> MITgcm-support at mitgcm.org
> http://mitgcm.org/mailman/listinfo/mitgcm-support