[MITgcm-support] stretched grid
Patrick Heimbach
heimbach at MIT.EDU
Tue Apr 27 11:36:36 EDT 2004
I guess this mail was spam, wasn't it...
-p.
Quoting Chris Hill <cnh at MIT.EDU>:
> Its fully possible and extremely easy as follows:
>
> 1 either Alistair checks in some code or
> 2 you write/edit about ten lines of code or
> 3 Alistair gives you the code he has, you try it and then check it in.
>
> all three are very doable I think!
>
> Chris
>
> > -----Original Message-----
> > From: mitgcm-support-bounces at mitgcm.org
> > [mailto:mitgcm-support-bounces at mitgcm.org] On Behalf Of
> > Patrick Heimbach
> > Sent: Tuesday, April 27, 2004 11:05 AM
> > To: mitgcm-support at mitgcm.org
> > Subject: RE: [MITgcm-support] stretched grid
> >
> > Does that mean that,
> > yes it's possible, but strictly,
> > it's not fully implemented?
> > -p.
> >
> > Quoting Alistair Adcroft <adcroft at MIT.EDU>:
> >
> > > Yes it is quite possible. The only thing the model does
> > wrong is that
> > > it assumes we're on a cube grid when reading the
> > curvilinear grid data
> > > - I have fixed this in my own version but need to check/rectify it
> > > with the latest cube stuff.
> > >
> > > The grid generation needs to give point-to-point distances
> > and surface
> > > areas for the four grids of model variables (T,U,V,Zeta) as
> > defined in GRID.h .
> > >
> > > A.
> > > --
> > > Dr Alistair Adcroft http://www.mit.edu/~adcroft
> > > MIT Climate Modeling Initiative tel: (617) 253-5938
> > > EAPS 54-1523, 77 Massachusetts Ave, Cambridge, MA, USA
> > >
> > > -----Original Message-----
> > > From: mitgcm-support-bounces at mitgcm.org
> > > [mailto:mitgcm-support-bounces at mitgcm.org] On Behalf Of Patrick
> > > Heimbach
> > > Sent: Monday, April 26, 2004 6:52 PM
> > > To: adcroft at MIT.EDU
> > > Cc: mitgcm-support at mitgcm.org
> > > Subject: [MITgcm-support] stretched grid
> > >
> > >
> > > Hi Alistair,
> > >
> > > is it possible to run the model on a stretched orthogonal grid?
> > >
> > > I reckon, it should be (fairly easy) as long as it is orthogonal,
> > > right?
> > > All that needs to be done should be to generate correct face cells
> > > that are then read by the model.
> > > Is there any documentation of what input the model needs (and which
> > > secret flags need to be set)?
> > >
> > > Thanks
> > > -Patrick
> > >
> > > _/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/
> > > Patrick Heimbach Massachusetts Institute of Technology
> > > FON: +1/617/253-5259 EAPS, Room 54-1518
> > > FAX: +1/617/253-4464 77 Massachusetts Avenue
> > > mailto:heimbach at mit.edu Cambridge MA 02139
> > > http://www.mit.edu/~heimbach/ U.S.A.
> > >
> > > _______________________________________________
> > > MITgcm-support mailing list
> > > MITgcm-support at mitgcm.org
> > > http://dev.mitgcm.org/mailman/listinfo/mitgcm-support
> > >
> > >
> > > _______________________________________________
> > > MITgcm-support mailing list
> > > MITgcm-support at mitgcm.org
> > > http://dev.mitgcm.org/mailman/listinfo/mitgcm-support
> > >
> >
> >
> > _/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/
> > Patrick Heimbach Massachusetts Institute of Technology
> > FON: +1/617/253-5259 EAPS, Room 54-1518
> > FAX: +1/617/253-4464 77 Massachusetts Avenue
> > mailto:heimbach at mit.edu Cambridge MA 02139
> > http://www.mit.edu/~heimbach/ U.S.A.
> >
> > _______________________________________________
> > MITgcm-support mailing list
> > MITgcm-support at mitgcm.org
> > http://dev.mitgcm.org/mailman/listinfo/mitgcm-support
> >
>
> _______________________________________________
> MITgcm-support mailing list
> MITgcm-support at mitgcm.org
> http://dev.mitgcm.org/mailman/listinfo/mitgcm-support
>
_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/_/
Patrick Heimbach Massachusetts Institute of Technology
FON: +1/617/253-5259 EAPS, Room 54-1518
FAX: +1/617/253-4464 77 Massachusetts Avenue
mailto:heimbach at mit.edu Cambridge MA 02139
http://www.mit.edu/~heimbach/ U.S.A.
More information about the MITgcm-support
mailing list