[MITgcm-support] problem with MNC

Manfredi Manizza mmanizza at ucsd.edu
Thu Aug 1 01:44:18 EDT 2013


Hi,

Hello !

I am in the early stages of running the new ECCO set-up LLc90.

I did a test run of one time step and all smooth wiritng the output in 
binary files.

Then I activated the MNC package. I created the a floder called "out1" 
where to store the output and I have this weird  problem

In STDERR.0000 I have got this :

(PID.TID 0000.0001) ** WARNING ** S.Edge of facet #  1 disconnected 
(facet_link=  0.00)
(PID.TID 0000.0001) ** WARNING ** S.Edge of facet #  2 disconnected 
(facet_link=  0.00)
(PID.TID 0000.0001) ** WARNING ** E.Edge of facet #  4 disconnected 
(facet_link=  0.00)
(PID.TID 0000.0001) ** WARNING ** E.Edge of facet #  5 disconnected 
(facet_link=  0.00)
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so bp gets switched off
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so sst gets switched off
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so scat gets switched off
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so altim gets switched off
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so altim gets switched off
(PID.TID 0000.0001) ** WARNING ** ECCO_CHECK_FILES: missing file 
definition so altim gets switched off
(PID.TID 0000.0001) ** WARNING ** S/R ECCO_CHECK: missing file:  for 
altimeter data so cost gets switched off
(PID.TID 0000.0001) GGL90_CHECK: Some form of convection has been enabled
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK: turbulent ice-ocn heat 
flux default changed.
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK:    To recover the old 
default : set
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK: SEAICE_mcPheePiston to 
the first ocn level
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK:    thickness divided by 
SEAICE_deltaTtherm.
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK: variable freezing point 
is new default.
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK:    To recover old 
constant freezing :
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK:    set SEAICE_tempFrz0 = 
-1.96 and
(PID.TID 0000.0001) ** WARNING ** SEAICE_CHECK: SEAICE_dTempFrz_dS = 0.
(PID.TID 0000.0001) CTRL_CHECK : ALLOW_U / VSTRESS_CONTROL used with exf 
& useAtmWind will have no effect
(PID.TID 0000.0001) ** WARNING ** S/R ECCO_CHECK: missing file:  for 
altimeter data so cost gets switched off
(PID.TID 0000.0001) ** WARNING ** CONFIG_CHECK: select_rStar=2 not right 
with nonlinFreeSurf=  2
(PID.TID 0000.0001) *** ERROR *** NetCDF ERROR:
(PID.TID 0000.0001) *** ERROR *** MNC ERROR: opening 
'out1/diags/budg2d_snap_set1.0000000000.t004.nc'

This is my data.mnc file :
# Example "data.mnc" file
# Lines beginning "#" are comments
  &MNC_01
# mnc_echo_gvtypes=.FALSE.,
# mnc_use_indir=.FALSE.,
  mnc_use_outdir=.TRUE.,
  mnc_outdir_str='out1',
  mnc_outdir_num=.FALSE.,
  monitor_mnc=.FALSE.,
  timeave_mnc=.TRUE.,
#
  pickup_read_mnc=.FALSE.,
  pickup_write_mnc=.FALSE.,
  mnc_read_theta=.FALSE.,
  mnc_read_salt =.FALSE.,
  &
# Note: Some systems use & as the
# namelist terminator. Other systems
# use a / character (as shown here).

In the out1 folder it writes only these files :

state*
grid*

but no tave* or sice* files.

Thanks in advance

Cheers
Manfredi





-- 
Dr. Manfredi Manizza
Geosciences Research Division
Scripps Institution of Oceanography
University of California San Diego
9500 Gilman Drive La Jolla, CA 92093-0244
email : mmanizza at ucsd.edu
tel   : +1-858-534-7094
web   : http://bluemoon.ucsd.edu/mmanizza/




More information about the MITgcm-support mailing list