[MITgcm-support] build error: obcs and ptracers with ecco

[Matthew Mazloff]

Oh...and based on your error you may have to add in

#ifdef ALLOW_OBCS_PRESCRIBE
CADJ STORE OBNptr0 = tapelev3, key = ilev_3
CADJ STORE OBNptr1 = tapelev3, key = ilev_3
#endif /* ALLOW_OBCS_PRESCRIBE */

for each boundary.....not sure if your code will have that

-matt




On May 19, 2008, at 12:23 PM, Suneet Dwivedi wrote:

> Hi Patrick,
> As per your advice I stripped down my adjoint model code so as to run
> it on a single processor. As I told you earlier also that it works
> fine without any error with obcs package but as soon as I try to
> include ptracers I get the following TAF error messages so that I am
> unable to build the adjoint code.
> ---------------------------------------------------------------------- 
> --------------------------------------
> 1325411 CADJ STORE OBNptr  = tapelev4, key = ilev_4
>                   ^
> *ERROR* : identifier not defined
> 1325413 CADJ STORE OBNptr0 = tapelev4, key = ilev_4
>                   ^
> *ERROR* : identifier not defined
> 1325414 CADJ STORE OBNptr1 = tapelev4, key = ilev_4
>
> and similarly for S,W,E boundaries.
> ---------------------------------------------------------------------- 
> ------------------------------------
>
> Attached herewith is the output of 'make adall' for your kind perusal.
> Please help me resolve this problem.
> Hoping for your reply,
> Suneet
>
> On Fri, May 16, 2008 at 3:03 PM, Patrick Heimbach  
> <heimbach at mit.edu> wrote:
>>
>> Hi Suneet,
>>
>> your error message has nothing to do with ptracers or obcs.
>> As I said, without seeing a toy setup, it's not clear what you are  
>> doing.
>> In your case, this kind of compile error typically arises when
>> instead of typing
>> make adall
>> you type
>> make
>> ("make" doesn't link the adjoint code, whereas "make adall" does).
>> -p.
>>
>>
>>
>> On May 16, 2008, at 1:37 PM, Suneet Dwivedi wrote:
>>
>>> Hi Everybody,
>>> Is this possible to build the adjoint code in which ptracers package
>>> works with open boundary conditions? For me, it failed. I am able to
>>> build the forward code successfully with both ptracers and obcs
>>> defined in packages.conf, but my build failed (see error message
>>> below) when I tried to do the same thing for adjoint code (by  
>>> allowing
>>> ecco, autodiff, cost and ctrl in packages.conf).
>>>
>>> -------------------------------------------------------------------- 
>>> ------------------------------
>>> the_model_main.o(.text+0x207): In function `the_model_main_':
>>> : undefined reference to `adthe_main_loop_'
>>> make: *** [mitgcmuv_ad] Error 1
>>>
>>> -------------------------------------------------------------------- 
>>> -------------------------------
>>> Is this a TAF problem? Do I need to make some changes in my code
>>> inorder to make it work?
>>> Hoping for your reply,
>>> Suneet
>>> _______________________________________________
>>> MITgcm-support mailing list
>>> MITgcm-support at mitgcm.org
>>> http://mitgcm.org/mailman/listinfo/mitgcm-support
>>
>> ---
>> Patrick Heimbach | heimbach at mit.edu | http://www.mit.edu/~heimbach
>> MIT | EAPS 54-1518 | 77 Massachusetts Ave | Cambridge MA 02139 USA
>> FON +1-617-253-5259 | FAX +1-617-253-4464 | SKYPE patrick.heimbach
>>
>>
>> _______________________________________________
>> MITgcm-support mailing list
>> MITgcm-support at mitgcm.org
>> http://mitgcm.org/mailman/listinfo/mitgcm-support
>>
>> <output.txt>
> _______________________________________________
> MITgcm-support mailing list
> MITgcm-support at mitgcm.org
> http://mitgcm.org/mailman/listinfo/mitgcm-support